Expert Answers about Chevrolet Vehicle Lights
- Dimensions Of The Tow Ready Vehicle To Vehicle Tail Light Converter # 118158
- The Vehicle to Vehicle Tail Light Converter # 118158 is approximately 2-7/8" wide x 2-3/8" tall x 3/4" deep.
view full answer... - How Much Power Does a Converter Box Draw on a Powered Wiring Harness
- The Tow Ready T-One Vehicle Wiring Harness, # 118551, for your 2012 Ford Escape is designed to draw as much power as needed to operate the trailer lights up to 15 amps or 7.5 amps for tail lights and 7.5 amps for stop and turn lights.
The powered converter allows you to tow trailers with more lighting and draws power directly from the vehicle battery when using the trailer lights. The amperage drawn by this converter depends on the amount and type of lights that you have on your trailer....
view full answer... - Do I Need Resistors When Installing the Optronics LED Backup Light item # BUL52CB?
- No, you shouldn't need a resistor like item # DI34ZR when installing the Optronics LED Backup Light for Trucks or Trailers item # BUL52CB. I say shouldn't because if you're installing these lights on a trailer your tow vehicle should supply plenty of power for them to function correctly. If you're installing these on a vehicle for additional lighting you will most likely need one on each light.
To install the Optronics LED Backup Light item # BUL52CB you will want to use the PVC Grommet...
view full answer... - What is the Wattage of the Bully Bumper Mount Backup Light
- Each Bully Bumper mount backup vehicle light # PL-807 is 55 watts. The backup light # PL-807 will come with one light.
The mounting hardware is also included.
view full answer... - Trailer Wiring Harness for 2013 Chevy Equinox for use With Light Strip
- The T-One Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector # 118264 is a great option for a wiring harness on your 2013 Chevy Equinox for use with your cargo carrier's light strip. I have added a link to a video install of this harness on a 2013 Equinox, as well as a link to the written instruction manual so you can see exactly how and where to install it. When not using it with your light strip/cargo carrier you will simply disconnect it and store it in the...
view full answer... - Will LED Light of the Prodigy P2 Brake Controller Stay on and Drain Battery, 2006 Chevy Silverado
- The light you are seeing on your Prodigy Brake Controller # 90185 will stay on for fifteen minutes after the controller sees its last activity. It only draws a few millivolts so you would not need to worry about your vehicle battery draining. If you let it sit for fifteen minutes you should see the light go away. The light should turn green once you connect your trailer connector from your vehicle to your trailer.
view full answer... - Does the Curt C56404 for a 2017 Audi Q5 Work w/ LED and Incandescent Trailer Lights?
- It will work with both. The Curt T-Connector Vehicle Wiring Harness item # C56404 sends the signals from your tail lights to the converter box that actually powers your trailer's lights. The direct line from the battery powers both LED and incandescent bulbs.
The Curt T-Connector Vehicle Wiring Harness item # C56404 is confirmed to fit a 2017 Audi Q5 with the factory supplied connector located in your cargo compartment.
If you do not have the factory connector you'll have to use the...
view full answer... - Will Self-Adhesive Magnetic Warning Light Bars Adhere to Aluminum or Fiberglass?
- I have a great alternative to the Blazer Amber Warning Light Bar # C4850AW. After some research, I confirmed that the Blazer Amber Warning Light Bar will not attract to aluminum or fiberglass. However, I recommend purchasing the Peterson Amber Revolving Halogen Warning Light Bar # 761A. Instead of mounting with a magnet, the Peterson permanently mounts on the installation surface and plugs into your vehicles auxiliary outlet.
If you are looking for a no-drill solution with a bit of a different...
view full answer... - Where can I attach the Peterson Light Kit
- I went to the warehouse and pulled the Peterson Tow Light Kit, # PE26UR. It can be placed anywhere that there is metal. It attaches securely with a strong magnet. You can place it anywhere so that it can be seen from the back. A good place is the top of the towed vehicle.
This kit will keep the tow vehicle and toad wiring separate, and provide stop turn and tail lights for towing your VW.
view full answer... - How Many Light Functions Does the Pedestal Mount Dual Face Trailer Light ST52RB Have
- The Pedestal Mount, Dual Face Trailer Parking and Turn Light, part # ST52RB, is not a 3 function light like the Pedestal Mount Trailer Stop, Turn and Tail Light, part # ST51RB.
You would not want a dual faced light as a stoplight as the brake lights should only be visible from the rear of the vehicle.
view full answer... - Does the Red Wire from the Hopkins Vehicle Wiring Converter Need to Be Wired In
- Yes, you will need to wire in the red wire from the Hopkins Vehicle Wiring Converter # HM46155 to the stop light circuit of your vehicle. Otherwise you will not have brake lights on your trailer.
Check out the video I attached that shows how this product would install onto a similar vehicle. Basically, you will use the included circuit tester to find the correct circuit to tap into, and then use the quick-splices to tap into that circuit.
view full answer... - Recommended Wiring Harness for a 2017 Jeep Grand Cherokee w/out the Towing Package
- Yes, it will. The T-One Vehicle Wiring Harness item # 118727 you were looking at will work with or without the Auto Stop/Start feature on. It gets it's signal directly from the tail lights which stay on when your vehicle is stopped at a light. This wiring harness is custom fit for the 2017 Jeep Grand Cherokee's that do not have the tow package.
I have linked an installation video below to help you get it set up.
If you are planning on towing you will also need a hitch item # 75699 and...
view full answer... - What Are The Functions Of The Wires On The Wiring Harness C59496?
- On the Vehicle Wiring Harness Kit w/ 4-Pole Trailer Connector and Installation Kit # C59496 shown in your picture the wires have the following functions:
Green wire is the passenger side turn signal
Yellow wire is the driver side turn signal
Brown wire is the tail lights
White wire is the ground
Red wire is the brake lights if your vehicle has separate brake lights/turn signals. If it does not the the red wire will get grounded with the white wire.
Black wire is the 12v power wire that...
view full answer... - Recommended Parts to Add a 7-Way Connector to a 2023 Chevy Trailblazer
- To add a 7-Way connector to your 2023 Chevy Trailblazer you will need two separate wiring harnesses. The first harness you'll need will be determined by whether or not you have LED or Incandescent lights. I have listed both options.
LED Lights - T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # TK26VR
Incandescent Lights - T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # TK39FR
The second harness you will need is the Universal Installation...
view full answer... - Diameter of Mounting Holes for GloLight LED Trailer Tail Light
- The GloLight LED Trailer Tail Light # STL111RFB has mounting holes which are 3/4" in diameter. You would also need a 3-wire pigtail # A45PB or # A47PB to connect the light to your trailer or vehicle.
I've added links to video reviews of these products for you to take a look at.
view full answer... - How Long is Power Cord on Demco Wireless LED Light Bar for Towed Vehicles
- The length of the power cord on the Demco Wireless LED Light Bar for Towed Vehicles part # DM36MV is 11-1/2'. This should be plenty to reach from the nearest outlet to the rear windshield.
view full answer... - How to Tow a 2010 Toyota Venza
- I am sorry but I checked with all of our vendors and no one has any parts listed for flat towing a 2010 Venza. The Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267 is pretty universal so it should work but I can't confirm.
I wanted to add that I pulled up the owners manual of your 2010 Toyota Venza and your vehicle is not recommended for flat towing. It says to use a tow dolly like the Demco Kar Kaddy item # DM9713045 to tow it behind your RV. This dolly also includes...
view full answer... - What Gauge Wire Does The Wesbar # 20016 5-Pole Vehicle End Trailer Connector Use
- The Wesbar # 20016 5-Pole Flat Vehicle End you referred to uses 18 gauge wire.
The yellow wire carries the left turn signal/brake lamp, the green carries the right turn/brake lamp, the brown carries the running light signal, the white wire carries the ground and the blue wire is connected to the reverse light circuit on the vehicle which then sends a signal to the hydraulic coupler to disengage the trailer brakes, so the vehicle can back without actuating the surge brakes.
view full answer... - Recommended 4-Way Wiring Harness for a 2023 Dodge Durango
- To add a 4-Way wiring harness to your 2023 Durango, I recommend the Curt T-Connector Vehicle Wiring Harness item # C56336. This custom-fit T-connector plugs into your Durango's wiring harness behind the tail lights. It will provide you with a 4-way vehicle connector that will control your trailer's lights.
I have linked an installation video below to help you get this harness installed.
view full answer... - Does the 4-Way Wiring Harness for a 2006 Camry Work w/ LED Trailer Lights?
- Yes, it will. The Curt T-Connector Vehicle Wiring Harness item # C55308 will work with a trailer that has LED lights. This harness is confirmed to fit a 2006 Toyota Camry. It will provide you with a 4-way connector.
I have linked an installation video below.
view full answer...
Go To Results